- Case agrupacables (6mm x 3.3m, 12mm x1.6m)
- Tape termorretráctil green UV (1m x 12mm, 25mm x 0.3m)
- 10 x female Connector Molex 4 pins
- 3 x female Connector of disk drive
- 1 x female Connector ATX20pin
- 1 x female Connector P4-12V 4 pins
- 1 x female Connector AUX6pin
- 2 x Connector S-TIES
- Tools
- Green Flanges UV
Presentation and view in detail:
The kit is presented in a transparent tea bag since which we can see all its interior. The kit is available in various colors; and all the elements that includes are reagents to the light UV. We throw in lack a manual of instructions.
Do us easier the task of the dismantling of the molex to pass the cases by the cables, itself enclosed in the package some tools. This will thank it more than one user.
With this side we will be able to extract conveniently the molex.
With this tool we will be able to remove the pins of the connector ATX and to open the eyelashes of the molex.
Here we see the collects-cables cases types that have: one of 12 mm of thickness, and another of 6 mm.
The cases of 6mm are used to decorate those cables that do not have a lot of thickness, like they can be the of the molex of 4 pins. The cases of 12 mm can serve us of great utility to group the cable that feeds the plate base.
his is the tape termorretráctil. Thanks to we will be able them to obtain a better one finished and besides the cases will be set perfectly, without any type of mobility in the case.
The kit is friendly flanges of the same color that the cases and the termorretráctil. What on of the flanges when we close is the convenient that itself cut. This we can do it with some pliers for example.
This is the connector ATX of 20 pins. The only difference with the Standard is the color, that shines under the light UV.
These are the molex female of 4 pins...
...this that of disk drive...
...this the female connector P4 - 12V of 4 pins...
...this it is the connector to help of 6 pins...
...another type of molex of 4 pins...
...And the connectors S-TIES; that neither they are green neither they are UV.
The source in which we are going to test the kit is a standard. Soon we will have a new concept as for esthetics of power supplies refers.
We proceed to dismantle the molex of 4 pins, for it we use the tool that the kit brings us. Simply we should introduce it for the orifice so that close the eyelashes, then we will be able to throw of the cable.
We carry out this process with the 4 cables of the ones that the molex is composed. The molex will remain us on the one hand and by another the 4 cables: yellow (12v), 2 black x (mass), and red (5v). You recall and to note in which position went placed each cable.
When we place it again, but this time in a molex of green color UV, we will have to expand lightly the eyelash of the "pin", thus after placing it again this will not be able to leave.
Now is the shift of the connector ATX of 20 pins. Perhaps be this connector the one that require more patience. You introduce it for the sides of the "pin" until closing the eyelashes. and already will be able to extract each "pin"...
...And thus Iran leaving one to one.
The aspect is similar al "pin" of the molex of 4 pins.
Recalling the disposition of these cables, I recommend you that, if is possible, take a picture to see that cable went in each place.
To dismantle the molex of disk drive we should apply certain pressure with a flat screwdriver in each one of the 4 sideburns.
This it is the aspect of one of the sideburns that form the connector molex of disk drive (floppy disk).
They arrived at this point, we have all our source dismantled. For complicate us not a lot we can group the pins of each connection molex with insulating... tape
...Besides that this will help us to pass the cables by the case collects-cables.
We place a case on one of the threads of our source. Treating the case with care so that itself be not frayed during this process. The more patience we have, better will be the finished.
To set the bases on the extreme that hits upon the power supply we will use only a flange, since if we place in this zone a termorretráctil we have to have a quite high care for burn not the remainder of the cables.
By the other extreme we stretch the case to extend it a little and tightening it, then we cut with care of cut not the cables of the interior and ready. Already we will have the case of the measure that need.
Now we can contract lightly and lengthwise the case so that remain to the height that we desire. After carrying out this, we place a flange for its subjection and we cut the remainder of the same one that on.
To leave a finished perfect, we cut a piece of termorretráctil. For fine cables, uses the termorretráctil fine. We place it as is shown in the photo, and applying heat the termorretráctil will shrink until remaining perfectly adapted.
They arrived at this step the eyelashes of the pins will be put toward inside, and we need to remove again to place their respective molex. For it we use the tool that see until manage to leave the sideburns as is shown in the photo. Already we are ready to place the molex.
You do not forget to place the molex as was placed before. This is something very serious, since if we place it al reverse we can cause some damage in our hardware.
We repeat the operation with the remainder of connections molex.; we see that we have not adjusted the termorretráctil al extreme of the molex, this should be done with tranquility and pledge to obtain a perfect result.
...And with the connector ATX.
This is the aspect that has now our source! Without Applying the light UV we realize the change that we have given him. Already it is passed time that in which the cables of the sources went entangled inside our boxes giving an esthetic little aspect.
We see therefore the color of the connections under the presence of light UV. Simply spectacular, nothing in comparison with the molex standard.
The collects-cables cases assembly and the tape termorretráctil offer a fantastic color (al the same as the molex) under the light UV.
The more dives lengthwise be the cases collects-cables, smaller will be the level of "drilling" that be appreciated in them.
View of the the cables in its entirety. No longer we will have reason to worry us if the cables of the source appear for our lateral window, but all the contrary thing, will be a genial complement for our boxes.
--------------------------------------------------------------------------------------------------------------------------
Bem ppl como me foi util esta informação, pensei tb em dxponibiliza-la para quem tiver duvidas nesta area
Apenas traduzi o txt pa ingles nada+... xpero k ajude!
